Minnetonka Minnesota Plumber MN

Sump Installation Minnetonka MN

With the spring flood season upon us, Minnesota homeowners can take action now to minimize costly basement flooding by checking their sump pump.

The combination of heavy spring rains falling on the ground that is still frozen is a recipe for an expensive disaster. Most homeowners fail to perform proper maintenance on their sump pump or have adequate homeowner’s insurance to guard against this problem. By following a few simple steps they can save themselves a lot of money and aggravation.

Sump Pumps Prevent Basement Flooding

Most people believe that after the snow melts that the threat of basement flooding goes away. But snow usually isn’t the issue; it’s the combination of the frozen ground thawing around the foundation of the home and the arrival of heavy spring rains that cause problems.

As soil thaws it is overly saturated with water, and when a spring rain adds few fresh inches, the water finds the easiest path to flow —usually along your home’s foundation, down to the basement and into your sump pump basin. If your sump pump fails, you’ll have a major water damage problem on your hands.

Sump pump failure is one of the most common causes for basement water damage. The number of calls for basement water damage cleanup explodes when spring arrives. And a majority of the time the cause is a sump pump problem. All too often it is beautiful finished basements that have been filled with 4 inches of water. It’s a heartbreaking site that is very expensive to fix.”

A sump pump is a last defense against flooding, pumping out water from the lowest section of the basement before the water level reaches the basement floor level. As groundwater levels rise, it is diverted into the sump hole. When the water reaches what is called ‘the critical level,’ the sump pump begins to pump the excess out through a pipe that leads outside and away from your foundation.

Just a few inches of water in a basement can cause tens of thousands of dollars in damage. According to the Insurance Information Institute, water damage— including sump pump overflow, frozen and burst pipes—has accounted for about 22 percent of all residential insurance claims. The average claim was $5,531. Unfortunately, many homeowners often overlook this on their policy and don’t have adequate protection against such damage.

The inability of a sump pump to handle runoff water from major downpours is not covered under a typical homeowner’s insurance policy, nor are they covered by flood insurance. This type of coverage must be purchased either as a separate product or as an endorsement to a homeowner’s policy.

A standard homeowner’s policy will not have coverage for a sump pump, or any existing drainage system. This includes a back-up through any drain, sink discharge, toilet, or sump pump failure.

The average lifespan of a sump pump is about 10 years, and they do eventually wear out. Fortunately, most sump pump problems can be avoided by a few regular maintenance checks and can easily be fixed by the homeowner.

Here’s a list of common sump pump problems and solutions for each. Before performing any sump pump maintenance, be sure to unplug any electrical power leading to the unit.

• Debris In The Sump Basin. Always check to make sure that the sump pit is free from debris. Children’s small toys and debris from items stored around the basin can get into the unit and hinder the float mechanism, causing it to fail. Test the float itself, since they can burn out over time. Fill the pit up with water, making sure it both starts and stops the sump pump as designed.

• Inspect The “Check” Valve. Sometimes, the check valve can be improperly installed. The check valves are set up so that when the sump pump shuts off, no water will go back into the sump pump. The check valve’s arrow should not be pointing toward the sump pump.

• Clean The Weep Hole. Some pumps will have a weep hole, usually between the sump pump and the check valve. You can clean this weep hole out with a toothpick or other tiny object. Be careful not to break anything into the weep hole.

• Clean the Impeller. This is a small filter that can easily become clogged. If your sump pump has stopped running suddenly, or has been making a whining noise, this could be the problem. The impeller should be connected to the sump pump with bolts and may need a good cleaning to work properly.

• Sump Pump Odor. Typical odors are caused from the sump pump trap. The trap always retains some water, but when water doesn’t flow into the basin during the dry seasons of the year, an odor starts to form. You can eliminate the odor by using a bleach-water mixture to cleanse the basin. One part bleach to five parts water will work. You can also fill the basin with water until the sump pump engages, cycling the water and helping to eliminate the odor.

• Install a Back-up Power Source. Purchasing a sump pump back-up power supply or a generator is a great idea to avoid overflow when you have a power outage. Most power outages are caused by heavy thunderstorms that bring huge amounts of rain very quickly. This is when you need your sump pump most. If you lose power the back-up system will take over to get rid of the water as the basin fills up. There are also water powered back-up systems that tap into your home’s water supply to provide the energy needed to run the pump. It is good to invest in the purchase of a back-up system now, rather than face the costs of a flooded basement.

Check Your Sump Pump Now To Avoid Basement Flooding

If more people would maintain their sump pumps like they do their automobile, they could save a lot of money and stress. A water damage restoration situation can really turn the lives of a family upside-down for a few weeks. Preventing the problem by checking the condition of their sump pump should be on their spring to-do list every year.

Sump Pit

  • Clean the pit each year after freeze-up. Weeping tile drainage may carry small amounts of soil, sand and debris into the pit from around your basement foundation.
  • Some water may remain in the pit and cause a musty smell if it sits for a long time. If so, you can flush the pit by adding fresh water until the pump removes the stale water.

Sump Pump

  • Check and test your sump pump each spring before the rainy season begins, and before you leave your house for a long time. Pour water into the pit to trigger the pump to operate.
  • Remove and thoroughly clean the pump at least once a year. Disconnect the pump from the power source before you handle or clean it.
  • Check the pit every so often to ensure it is free of debris. Most pumps have a screen that covers the water intake. You must keep this screen clean.

Sump Pump Discharge Pipe

  • Check the place where the discharge pipe leaves the house. If the pipe is discharging right against the basement wall, the water will drain down into the weeping tiles and continue to recycle through the system.
  • Check the discharge point regularly to make sure that nothing is blocking the flow.
  • If your pump runs frequently in the winter, and the resulting ice is causing hazardous conditions on the lawn and sidewalks, call your municipal office.

Backwater Valve

A backwater valve is a device that prevents sewage in an overloaded main sewer line from backing up into your basement. The valve automatically closes if sewage backs up from the main sewer. A properly installed backwater valve must be placed so that sewage backup will be stopped and not come out through other outlets in your basement, such as sinks, toilets, showers and laundry tubs.

  • Make sure that you can get at the valve at all times.
  • Check the valve regularly and remove any material that may prevent the valve from operating properly.

You will normally require a permit and inspection to install a backwater valve and sump pit. Since part of the basement floor will be dug up and since proper placement of these items is important, we recommend that you use a qualified Minnesota plumbing contractor.

Stay current on flood risk in your area.

Leave a Reply