Minneapolis Plumber MN | St Paul Plumbing Service Minnesota

Money Saving Tips To Reduce Your Utility Bill

As we become more and more aware that we may be using water at an unsustainable pace, the idea of water footprints-the amount of water an individual uses-is becoming more common. Remember that water is a valuable resource that shouldn’t be wasted. Your water is clean, safe and convenient but you have to pay for its treatment and the system to deliver it to you. By conserving water in your home, you also save energy needed to heat it or run appliances.

Water and Sewer bills can be as high as $500 for the average household.  According to the EPA, you can save up to $170 per year and conserve resources by making just a few small changes in your water usage.  From replacing old and inefficient appliances to making small changes in your home, you have the potential to realize savings.

Small Water Savings Can Have A Big Impact

Bathrooms

Be aware of toilet leaks. Two thirds of the water used in an average home is used in the bathroom, and a lot of it goes into the sewer. From 2-7 gallons of water are used every time a toilet is flushed.  That’s a lot of water over the course of a year.  It is estimated that 20% of all toilets leak, and some so slowly that a leak can go undetected for years. Do not use the toilet to flush items that can go in a wastebasket or garbage can.

You may have been advised to take showers rather than baths to conserve water. If you take a long shower, however, you may use more water than if you took a bath. Long, hot showers not only waste water but also energy to heat the water. Consider using reduced-flow devices for showerheads.

Don’t leave the water running while you shave or brush your teeth. You are just running clean water down the drain.

Kitchens

Did you know that a faucet in the kitchen, dripping one drip per second can add up to 3000 gallons of wasted water per year.  A drip may seem like a small deal but it can cost you a bunch in the long run.  Faucet drips can typically be fixed by replacing the seals.  Seal kits are inexpensive and fairly simple to install.

Be sure the dishwasher is fully loaded before running it. There is no need to rinse dishes before putting them in the dishwasher.

If you wash dishes by hand, do not let the water run while washing or rinsing. Don’t let the water run while cleaning vegetables or other foods, either. Use a large pan or dish for rinsing.

Store drinking water in the refrigerator rather than letting it run until it’s cold.

Laundry

Be sure to have full loads, or use the automatic controls for smaller loads. Use cold water for rinsing.

Outdoors

Of course we all want to have a nice green lawn.  Keeping your lawn and garden green can account for at least 30% of your household water usage. Don’t water on a fixed schedule or if rain is forecast — water grass or plants only if they show signs of needing it. Water during the coolest part of the day to avoid excess evaporation and let the water sink in slowly. Water applied too fast runs off into storm sewers.

When washing the car, use a bucket of water for washing and run the hose only for rinsing.

Plumbing

Install shutoff valves for appliances and fixtures in case a pipe blows out. Most importantly, check for a main shutoff valve that turns off water to the whole house, and make sure that it works.

How can I tell if I have any water leaks?

Newer types of water meters have a leak indicator on the face of the dial. It is a triangular or diamond-shaped indicator that revolves 354 times for every gallon of water that passes through the meter. Note: You may see what looks like water on the face of the dial. It is oil that prevents corrosion and increases the life of the dial mechanism. It does not enter the water supply and does not affect the quality of the water delivered to the customer.

To check for leaks, look at the indicator when no one is drawing water. It should not be moving. If it is moving, check every plumbing fixture at the property, i.e., toilet, sink, outside sprinkler, washer, etc. Shut off the valves that supply each fixture, one by one, and check the indicator after each shutoff. When closing a valve stops the indicator from moving, or slows its movement, you have found the location of a leak. There may be more than one leak!

Be sure to check toilets at the property! Toilet leaks are the most common and are hard to see or hear. Put food coloring or laundry bluing in the toilet tank and wait 10 minutes. Do not flush the toilet during this time. If the coloring appears in the toilet bowl, there is a toilet leak. Also, if you hear the toilet refilling and no one has used it, there is a leak. A major toilet leak can waste 800 cubic feet of water a day — which would cost over $24.00 for water and over $23.00 for sewer each day. That adds up to over $1,400.00 a month!

Look for leaky faucets, too. A fast drip from a faucet wastes about 265 gallons a day — which would cost about $1.08 for water and $1.05 for sewer per day. That’s almost $65 a month! Repair leaky faucets and toilets promptly — do it yourself or call a Minnesota plumber because these leaks cost money. Once the leak is repaired, check the leak indicator again and make sure all leaks are repaired.

By keeping your eye on a few of the potential water wasting areas of your home, you can help to conserve a precious natural resource and save yourself utility costs.

Some information provided by the City of Minneapolis
As we become more and more aware that we may be using water at an unsustainable pace, the idea of water footprints-the amount of water an individual uses-is becoming more common.

One Response to “Minneapolis Plumber MN | St Paul Plumbing Service Minnesota”

  1. […] tank. Manufacture. This slip is poured into the space among plaster of Paris molds. Bathroom bowl, toilet reviews rim, rest room tank and rest room tank lid all need different molds. The molds are assembled and […]

Leave a Reply